MP8

• 8 Zones
• 100/70V Line or Low Impedance Applications
• Includes 2.5 inch speaker with volume control
• Simply select any amplifier via the front panel switch and you can monitor its output through the speaker and via an LED array.
• Signal Present LED provided for each zone for easy troubleshooting
• Loop in, loop out terminal strips for inputs from amplifiers and outputs to speakers
• 2 RU
• AC/DC

Download Specification Sheet - Colour - 225k B&W - 87k

Download Operations Manual - 439k

• The Australian Monitor Installation Series AMIS26 is a high quality 2 input, 6 output distribution amplifier. The AMIS26 provides a low noise, feature packed, signal routing solution to cover a wide range of installation needs, at a contractor friendly price.
• Inputs
  The AMIS26's 2 inputs can be balanced or unbalanced and each input's sensitivity can be switched between Mic and Line level. Each of the AMIS26's inputs is individually assignable to any of the 6 outputs via front panel DIP switches
• Outputs
  The 6 outputs can again be balanced or unbalanced and feature up to -60dB of attenuation so they can be run as any combination of line level or mic level outputs.
• Controls
  Input Level: The input level controls are screw diver adjustable trim pots. The input level can boost or cut the input signal by up to 15dB.
  Input Assign Switches: The recessed DIP switches assign either input A or B to a desired output.
  Output Level: The output level controls are screw driver adjustable trim pots. This level control attenuates the output level, with a range from -60dB at "Minimum" position, to 0dBat "Maximum" position.
  Output Level DIP switch: This switch will change the output sensitivity of the desired output from Mic to line level.
  24 VDC Phantom Power is also individually switchable per input
• Metering
• Input Level Meter: These 4 segment LED meters show the strength of each of the AMIS26's input signals. LED segments are calibrated to the following level markings
  and show the following colours -20dBu (green), -10dBu (green), 0dBu (yellow), +10dBu (red).
• Phantom Power
  -24 VDC Phantom power is also individually switchable per input.
• Power Input 24 VDC (regulated); 12VA max.
• Output Mic/Line Switch 28dB
• Noise -89dB
• Frequency Response (0dB/-3dB) 10Hz - 50kHz
• Total Harmonic Distortion Line In (XLR/RCA) 0.02%; Mic In (XLR) 0.1%
• Crosstalk Better than 80dB
• Phantom Power 24VDC
• Input Sensitivity Line (XLR) 775mV (0dB); Mic (XLR) 10mV (-37dB); Line (RCA) 775mV (0dB)
• Dimensions 44.0 x 482.0 x 168.0 (H x W x D) mm
• Weight Net 2.5 kg (5.5 lb), Shipping 3.0 kg (6.6 lb)
• All measurements done with levels set In/Out at 0dB;
• All measurements referenced to 0dBu (0.775mV)

Download Specification Sheet - Colour - 348k

Download Operations Manual - 226k

Architectural and Engineering Specifications
The distribution amplifier shall be a high quality two input, six output distribution 1RU device. The unit will have two inputs which can be balanced or unbalanced and each input's sensitivity can be switched between Mic and Line level via dip switches. Additionally these front panel dip switches will allow any of the inputs to be routed to any of the six outputs. The units shall provide a four segment LED level meter per input.
The unit shall provide 24 VDC Phantom power which is to be individually switchable per input.
The units outputs shall be balanced or unbalanced and feature up to -60dB of attenuation so that they can be run as any combination of line level or mic level outputs.
The distribution amplifier shall be an Australian Monitor Installation Series AMIS26.