| Australian Monitor Mixer Amps |
Back to Australian Monitor Index Page |
| Product Picture |
Part Number |
Description |
A & E Specifications |
 |
AMIS60 |
- 6-Zone Commercial paging amplifier
- 60 Watt, 6 zone output 70 Volt, 8 Ohm Output complete with all call.
- Balanced XLR & Tape Outputs
- 4 x dual balanced mic/line inputs
- Built in phantom power with defeat provided on all mic inputs
- Auto limiter built in
- Overall bass & treble, and master volume control
- Built in preanounce, alert, evacuate and bell tone (preanounce on front panel is defeatable)
- Built in VOX muting on inputs 1 & 2
- 600 Ohm transformer balanced telephone input for paging
- VOX relay outputs
- VCA remote of master volume control
- 2 space, rack mounted, 120VAC or 24VDC powered
- cUL Certified
Download Specification Sheet - Colour B&W
|
Architectural and Engineering Specifications
The mixer amplifier shall have four universal input channels, each comprising of a balanced microphone input with XLR female sockets and an auxiliary input using dual RCA sockets.
The 70 volt line speaker outputs should be able to be switched via a six position selector with "all call".
A balanced XLR output to drive additional power amplifiers shall also be provided.
The amplifier master section shall include one master gain control, two EQ controls, one with 12dB of cut and boost at 100Hz and the other with 9dB of cut and boost at 10kHz.
Speaker outputs shall be transformer isolated at 70 volt and 8 ohms.
The amplifier must be capable of delivering 60 watts RMS into an 80 ohm inductive load, with less than 0.5% distortion measured at 1kHz and with system hum and noise less than -74dB.
The amplifier shall be an Australian Monitor Installation Series model AMIS60.
|
 |
AMIS120 |
- 6-Zone Commercial paging amplifier
- 120 Watt, 6 zone output 70 Volt, 8 Ohm Output complete with all call.
- Balanced XLR & Tape Outputs
- 4 x dual balanced mic/line inputs
- Built in phantom power with defeat provided on all mic inputs
- Auto limiter built in
- Overall bass & treble, and master volume control
- Built in preanounce, alert, evacuate and bell tone (preanounce on front panel is defeatable)
- Built in VOX muting on inputs 1 & 2
- 600 Ohm transformer balanced telephone input for paging
- VOX relay outputs
- VCA remote of master volume control
- 2 space, rack mounted, 120VAC or 24VDC powered
- cUL Certified
Download Specification Sheet - Colour B&W |
Architectural & Engineering Specifications
The mixer amplifier shall have four universal input channels, each comprising of a balanced microphone input with XLR female sockets and an auxiliary input using dual RCA sockets. The 70 volt line speaker outputs should be able to be switched via a six position selector with "all call". A balanced XLR output to drive additional power amplifiers shall also be provided. The amplifier master section shall include one master gain control, two EQ controls, one with 12dB of cut and boost at 100Hz and the other with 9dB of cut and boost and 10kHz speaker outputs shall be transformer isolated at 70 volt, 4 & 8 ohms. The amplifier must be capable of delivering 120 watts RMS into an 40 inductive ohm load, with less than 0.5% distortion measured at 1kHz and with system hum and noise less than -74dB. The amplifier shall be an Australian Monitor Installation Series model AMIS120.
|
 |
AMIS120XL |
- 120 Watt Mixer Commercial paging amplifier
- 120 Watt, 8 zone low level outputs, 1 zone 70 Volt, 4 & 8 Ohm Output complete with all call.
- Balanced XLR & Tape Outputs
- 8 x dual fully variable and balanced mic/line inputs
- Built in phantom power with defeat provided on all mic inputs
- Auto limiter built in
- Overall bass midrange & treble, and master volume control
- Built in preanounce, alert, evacuate and bell tone (preanounce on front panel is defeatable)
- Built in multi-level VOX muting: input 1 mutes 2-8, Input 2 mutes 3-8, Input 3 mutes 4-8
- 600 Ohm transformer balanced telephone input for paging
- VOX relay outputs to trigger over-ride relays, etc.
- signal present LED
- VCA remote of master volume control
- 2 space, rack mounted, 120VAC or 24VDC powered
- cUL Certified
Download Specification Sheet - Colour B&W |
Architectural & Engineering Specifications
The mixer amplifier shall have eight universal input channels, each comprising of a balanced microphone input with XLR female sockets and an auxiliary input using dual RCA sockets. A balanced XLR output to drive additional power amplifiers shall also be provided. The master output may be controlled remotely via a VCA control. An insert point is provided for the addition of signal processing. A vox triggered relay output (for external devices) shall also be included. The amplifier master section shall include one master gain control, three EQ controls, one at 100Hz with 12dB of cut and boost, one at 600Hz with 12dB cut and boost and the other with 9dB of cut and boost at 10kHz. Speaker outputs shall be transformer isolated at 70 volt, 4 & 8 ohms. The amplifier must be capable of delivering 120 watts RMS into a 40 inductive ohm load, with less than 0.5% distortion measured at 1kHz and with system hum and noise equal to or better than -74dB. The amplifier shall be an Australian Monitor Installation Series model AMIS120XL.
|
 |
AMIS250 |
- 250 Watt Mixer Commercial paging amplifier
- 250 Watt, 6 zone low level outputs, 1 zone 70 Volt, 4 Ohm Output complete with all call.
- Balanced XLR & Tape Outputs
- 6 x dual fully variable and balanced mic/line inputs
- Built in phantom power with defeat provided on all mic inputs
- Auto limiter built in
- Overall bass midrange & treble, and master volume control
- Built in preanounce, alert, evacuate and bell tone (preanounce on front panel is defeatable)
- 600 Ohm transformer balanced telephone input for paging
- VOX relay outputs to trigger over-ride relays, etc.
- VCA remote of master volume control
- 2 space, rack mounted, 120VAC or 24VDC powered
- Fan cooled for added reliability
- cUL Certified
Download Specification Sheet - Colour B&W |
Architectural & Engineering Specifications
The mixer amplifier shall have six universal inputs each comprising of a balanced microphone with XLR female sockets and an auxiliary input using dual RCA sockets. A balanced XLR output to drive additional power amplifiers shall also be provided. The amplifier master section shall include one master gain control, three EQ controls, one with 12dB of cut and boost at 100Hz, one with 12dB cut and boost at 600Hz and the other with 9dB of cut and boost at 10kHz. Speaker outputs shall be transformer isolated at 70 volt and 4 ohms. The amplifier must be capable of delivering 250 watts RMS into a 20 inductive ohm load, with less than 0.5% distortion measured at 1kHz and with system hum and noise less than -74dB. The amplifier shall be an Australian Monitor Installation Series model AMIS250.
|
|
