 |
AMIS120P |
- Commercial Power Amplifier
- 120 Watt, 70 Volt, 4 & 8 Ohm Output.
- Rear panel level control
- Balanced line level inputs with parallel outputs
- Built in current limiter
- Signal present LED
- 2 space, rack mounted, 120VAC or 24VDC powered
- cUL Certified
Download Specification Sheet - Colour B&W
|
Architectural and Engineering Specifications
The 120 watt power amplifier shall be designed to run 70 volt line audio systems. The unit shall also feature a 4 and 8 ohm output. The amplifier may be desk or rack mounted. The amplifier must be capable of delivering 120 watts into an 40 ohm inductive load with less than 0.5% distortion measured at 1kHz and with system hum and noise of -80dB or better. Internal current limiting shall protect the amplifier from both overload and overdrive conditions. The amplifier shall be an Australian Monitor Installation Series model AMIS120P.
|
 |
AMIS1202P |
- Commercial Power Amplifier
- 2 x 120 Watt amplifiers, one chassis
- dual x 70 Volt, 4 & 8 Ohm Output.
- Rear panel level control
- Balanced line level inputs with parallel outputs
- Built in current limiter
- Signal present LED
- 2 space, rack mounted, 120VAC or 24VDC powered
- cUL Certified
Download Specification Sheet - Colour B&W |
Architectural and Engineering Specifications
The power amplifier shall be a dual channel model capable of delivering 120 watts RMS per channel into 70 volt line and 4/8 ohm loads. The unit shall feature a signal-present LED per channel. Speaker connection shall be via a rear panel barrier strip. The amplifier shall have two balanced XLR inputs per channel, one of which can be used to feed additional power amplifiers. The unit shall also include fuse protection for overload and short circuit conditions. The unit shall also feature generous heatsinking for reliable operation in extreme conditions. The unit shall be of high quality suitable for continuous, reliable performance. It shall have a frequency response of no less than 60Hz - 23kHz (- 3dB). Distortion shall not exceed 0.5% at 1kHz. The signal to noise ratio shall be -80dB (on 100V setting) or better. The power amplifier shall be packaged in a rugged 2 rack unit metal chassis suitable for desk or rack mounting. The amplifier shall be an Australian Monitor Installation Series model AMIS1202P.
|
|
AMIS250P |
- Commercial Power Amplifier
- 250 Watt, 70 Volt, 4 Ohm Output.
- Rear panel level control
- 10k Balanced inputs with parallel outputs
- Auto limit protection
- Thermally protected by built in fan
- 2 space, rack mounted, 120VAC or 24VDC powered
- cUL Certified
Download Specification Sheet - Colour B&W |
Architectural and Engineering Specifications
The 250 watt power amplifier shall be designed to run 70 volt line audio systems. The unit shall also features a four ohm output. The amplifier may be desk or rack mounted. The unit shall feature high temperature protection with front panel indication. An in built auto temperature sensing fan shall cool the unit when required and automatically turn off again once the amplifier is running at the correct temperature. The amplifier must be capable of delivering 250 watts into a 20 ohm inductive load with less than 0.5% distortion measured at 1kHz and with system hum and noise less than -74dB. The amplifier shall be an Australian Monitor Installation Series model AMIS250P.
|
|
AMIS480P |
- Commercial Power Amplifier
- 4 x 80 Watt, 70 Volt, 4 Ohm Output.
- Rear panel level control per channel
- 10k Balanced inputs with parallel outputs
- Auto limit protection
- Thermally protected by built in dual fan
- 2 space, rack mounted, 120VAC or 24VDC powered
- NRTL Certified
- Ground lift switches per channel
- Perfect for partnering with DigiPage or ZRM4
Download Specification Sheet - Colour
AMIS480P Specifications
Power Output (1% THD, all channels driven) 4 x 80W
Freq. Response (1W) 80Hz - 20kHz
Power Bandwidth (-3dB) 85Hz - 20kHz
THD (1kHz, -3dB) Less than 0.5%
S/N Ratio 94dB (ref 100V)
Crosstalk 1kHz 80dB; 20Hz - 20kHz Better than 60dB
Input Sensitivity 0.775V RMS (0dBu)
Input Impedance 20KΩ
Voltage Gain (pot at max) 100V out 129 (42dB);
70V out 90 (39dB); 4Ω out 23 (27dB)
Output Regulation (1kHz) 95%
Dimensions (h x w x d) 88mm x 483mm x 432mm
(4.36" x 19" x 17")
Weight 20kg (44lb)
Shipping Dimensions (h x w x d) 230mm x 540mm x 550mm (9.1” x 21.3” x 21.7”)
Shipping Weight 24kg (53lb)
|
Architectural and Engineering Specifications
AMIS480P is a robust, highly featured 4 channel power amplifier.
Offering 4 independent channels, each delivering 80 watts into 4 ohms or 70/100 volt line, the AMIS480P is designed to operate in extreme conditions to give the contractor the most reliable 4 channel amplifier available today.
Engineered with maximum attention to channel isolation, with individual ground lift switches and level control for each channel, the AMIS480P will operate as 4 individual amplifiers in a rack space friendly, 2RU chassis.
For ease of installation, each channel input can be routed to the next channel via rear panel link switches, eliminating the need for daisy chaining or Y-split cables. The AMIS480P also offers signal present and clip LED indicators for each channel as well as a thermal protect indicator.
The AMIS480P is a significant advance in 4 channel amp design offered at a contractor friendly price.
|
